Understanding the Cause of Burnt Pods
If you are a vaper, then you must have experienced the unpleasant taste of a burnt pod at some point. This can be a major disappointment as it ruins the flavor of your e-liquid and can be harmful to your health. To avoid this, it is important to understand why burnt pods occur in the first place.
The most common cause of burnt pods is a lack of e-liquid. This can happen if you have not primed your pod before using it. Priming involves saturating the cotton in the pod with e-liquid before vaping to ensure that it is fully soaked. If you don’t do this, your pod will not have enough e-liquid to vaporize, resulting in a dry hit and a burnt taste.
Another cause of burnt pods is chain vaping. This refers to the act of taking vape hits in quick succession without giving your pod enough time to cool down. As a result, the pod becomes too hot, and the e-liquid is vaporized faster than it can be replenished. This leads to a burnt taste and can also damage the pod’s coil.
Using high wattage is also a common cause of burnt pods. Pods are designed to work at a specific wattage range, and if you exceed this range, you risk burning the coil. This is especially true for pods with low resistance coils. To avoid this, always check your pod’s recommended wattage range and adjust your device accordingly.
Poor quality e-liquids can also contribute to burnt pods. Some e-liquids may contain impurities or sweeteners that can clog up your pod’s coil, leading to a burnt taste. It’s always important to use high-quality e-liquids from reputable manufacturers to ensure that your pods last longer and taste better.
Finally, improper storage or handling of your pods can also lead to burnt hits. If your pod is exposed to sunlight or heat for too long, the e-liquid can break down and become less effective. Similarly, if you drop or mishandle your pod, it can become damaged and affect the quality of your vaping experience.
To summarize, burnt pods can be caused by a lack of e-liquid, chain vaping, high wattage, poor quality e-liquids, and improper storage and handling. By understanding these causes, you can take steps to avoid them and enjoy a better vaping experience.
Advanced Techniques for Reviving Burnt Pods
If you’ve accidentally burnt your pod and it tastes like ash or you get a burnt taste with every hit, don’t worry! There are a few techniques that you can try that might just revive your burnt pod.
Here are 4 advanced techniques for reviving burnt pods:
1. Remove the Wick
The wick is the part of the pod that soaks up the e-juice. This is the part that burns easily, and once it’s burnt, it will give you a horrible taste with every hit. To fix this, you can try to remove the wick entirely and replace it with a new one.
To do this, take the pod apart, remove the wick, and then pack the pod with a new wick. Be sure to prime the new wick with e-juice before using it to avoid any burning issues.
2. Use a Dental Floss to Clean the Pod
If the burning taste still persists after trying the first method, then try using dental floss to clean the pod. Take a piece of dental floss and run it through the holes in the pod. This will help to remove any excess gunk that might be causing the burning issue. Be gentle when doing this to avoid damaging the pod.
After cleaning with the dental floss, insert a new coil, prime it with the e-juice, and let it sit for a few minutes before taking a hit.
3. Soak the Pod in Vodka or Grain Alcohol
If you’ve tried the first two methods and the burnt taste still persists, try soaking the pod in vodka or grain alcohol. This can help to break down any gunk that might be stuck in the pod.
Take the pod apart and remove the coil and wick. Soak the pod in vodka or grain alcohol for an hour or two. After soaking, rinse the pod with water and let it dry completely before using it again.
4. Dry Burn the Coil
If you don’t have a new coil or wick to replace the burnt one, you can also try a dry burn technique. This involves heating up the coil to kill the gunk that might be causing the burnt taste.
To do this, remove the pod, disassemble the coil, and take out the wick. Hold the coil under the tap for a few seconds to remove any excess e-juice. Then, reassemble the coil, dry burn it for 2-3 seconds, and repeat until the gunk is gone. Take care when handling the hot coil.
After following these four methods, it’s quite likely that your burnt pod will be revived. It’s important to keep in mind, however, that these techniques aren’t always effective. If none of these techniques work, it might be time to invest in a new pod or device altogether.
Prevention Techniques for Future Burnt Pod Incidents
Preventing burnt pods is a crucial aspect of vaping safety. Here are some prevention techniques:
1. Keep your pod devices clean
One of the simplest prevention techniques is keeping your pod devices clean. Regular cleaning helps prevent debris build-up, which can lead to burnt hits. You can use a cotton swab or cloth with some isopropyl alcohol to clean your devices.
2. Check your pod’s e-liquid level
Make sure that your pod has enough e-liquid to prevent dry hits. Dry hits occur when the coil heats up without e-liquid, causing it to burn. Ensure that your pod’s e-liquid level is always above the minimum fill line.
3. Prime your pods before use
Primed pods ensure that e-liquid hits the coil faster, preventing dry hits. To prime, you need to add a few drops of e-liquid and let it soak in the cotton for a while, allowing the cotton to saturate. After priming, make sure to wait for a few minutes and let the pod sit. It is ideal for priming only when you are about to use your device.
4. Avoid chain vaping
Chain vaping, where you hit the device multiple times in a row, can cause the coils to overheat, leading to a burnt pod. Taking a break between hits allows your device to cool down. Your pods will last longer if you avoid chain vaping.
5. Use e-liquids with the correct VG/PG ratio
The VG/PG ratio in your e-liquid affects the thickness, flavor, and vapor production. Using e-liquids with the wrong VG/PG ratio can cause your pods to burn quickly. High VG liquids tend to be thicker, and low PG liquids tend to be thinner. If you are not sure of the VG/PG ratio, you can read the label or consult with the vape store salesperson.
Now that you have learned the techniques to prevent burnt pods, ensure that you always practice them. Prevention is better than cure. Happy vaping!
